607 reviews analysed
1. Ewigkeit 12V 40W Ceramic Cartridge Heater and 3950 100K NTC Thermistor with Female Pin Head for RepRap 3D Printer Heatbed or Hot End
Feature
- Thermistor Color : white,Cartridge Heater Material: 304 Stainless Steel
- Voltage: 12v, Power: 40w,Diameter: 6mm
- Length: 20mm
- Temperature sensor 100KΩ accuracy of ± 1%
- Conviniently pre-wired with 1 meter long high temperature teflon insulated wiring
- Support for NTC 3950 is included in Marlin firmware, use TEMP_SENSOR 11 in firmware configuration
2. BCZAMD 12V 50W Upgraded Ceramic Cartridge Heater Wire 1M 3D Printer Accessories Heating Tube 620mm for Reprap Prusa Mendel i3 MK3 MK10 Maker Select V2 3D Printer Parts V6 Hotend J-head Extruders, 3Pcs
Feature
- Apply to Creality CR-10S Pro, CR-X, Ender 3, Ender 3X, Ender-3 Pro, Anet A8, Maker Select V2.1, Monoprice v2, Wanhao Duplicator 3D Printer, V6 Volcano MK8 MK9 MK10 Extruder/Hotend etc.
- The improvement compared to ordinary red heating tube:
- 1.From the original ordinary 0.3-line high-temperature line to 0.5-line thick white high-temperature line, can bear higher temperature, and looks more beautiful.
- 2.From the original 40W power to 50W, the maximum temperature increases from 300-31℃ to 340-350℃. Can be used with the new HT-NTC100K temperature thermistor.
- 3.The new version heater used in all imported skills, the use of 304 stainless steel, with the internal use of 2080 nickel chrome wire to achieve maximum service life.
Description
After-sales guarantee: each defective item can be replacement for free or refund. If any question, please feel free to contact or QA us, we will try our best to service you
Specification
Voltage: 12V
Power: 50W
Heating head size: 6 x 20mm
Heating head material: 304 stainless steel
Line length: 39inch /1M
Line thick: 0.5 mm?2; (The cross section of the copper wire inside the heater is 0.5mm?2;)
Color: as shown in the picture
Working Temperature: < 350="">
Single-end heating tube use instructions:
1.The effective heating part of the single-end heating tube must be kept dry.
2.The electrical joint of the single-ended heating pipe should be placed outside the insulation layer and the heating chamber. The working voltage should not exceed 10% of its rated value, and the casing should be effectively grounded.
3.The working environment of the electric heating element, the temperature is not more than 95 degrees, no explosive, corrosive gas.
4.The electric heating element should be stored in a dry place and should not be damp.
Package listing:
3 x 12V 50W Ceramic Cartridge Heater
3. BCZAMD 24V 50W Upgraded Ceramic Cartridge Heater Wire 1M 3D Printer Accessories Heating Tube 620mm for Reprap Prusa Mendel i3 MK3 MK10 Maker Select V2 3D Printer Parts V6 Hotend J-head Extruders, 3Pcs
Feature
- Apply to Creality CR-10S Pro, CR-X, Ender 3, Ender 3X, Ender-3 Pro, Anet A8, Maker Select V2.1, Monoprice v2, Wanhao Duplicator 3D Printer, V6 Volcano MK8 MK9 MK10 Extruder/Hotend etc.
- The improvement compared to ordinary red heating tube:
- 1.From the original ordinary 0.3-line high-temperature line to 0.5-line thick white high-temperature line, can bear higher temperature, and looks more beautiful.
- 2.From the original 40W power to 50W, the maximum temperature increases from 300-31℃ to 340-350℃. Can be used with the new HT-NTC100K temperature thermistor.
- 3.The new version heater used in all imported skills, the use of 304 stainless steel, with the internal use of 2080 nickel chrome wire to achieve maximum service life.
Description
After-sales guarantee: each defective item can be replacement for free or refund. If any question, please feel free to contact or QA us, we will try our best to service you
Specification
Voltage: 24V
Power: 50W
Heating head size: 6 x 20mm
Heating head material: 304 stainless steel
Line length: 39inch /1M
Line thick: 0.5 mm?2; (The cross section of the copper wire inside the heater is 0.5mm?2;)
Color: as shown in the picture
Working Temperature: < 350="">
Single-end heating tube use instructions:
1.The effective heating part of the single-end heating tube must be kept dry.
2.The electrical joint of the single-ended heating pipe should be placed outside the insulation layer and the heating chamber. The working voltage should not exceed 10% of its rated value, and the casing should be effectively grounded.
3.The working environment of the electric heating element, the temperature is not more than 95 degrees, no explosive, corrosive gas.
4.The electric heating element should be stored in a dry place and should not be damp.
Package listing:
3 x 24V 50W Ceramic Cartridge Heater
4. MK8 Extruder Hot End Part Assembled DIY Hotend, 0.4mm Nozzle 12V 40W Heater Including for RepRap、CR 10 3D Printer 1.75mm Filament
Feature
- Package include:22 pcs 3d printer nozzles (output diameter ) 22 x 0.4mm, With storage box packaging.
- COMPATIBILITY: mk8 nozzle are compatible with Anet A8, Creality CR-10, Tevo Tarantula, MK8 makerbot, duplicator, prusa i3 and reprap,Compatible with all 1.75mm ABS/ PLA 3D printer.
- Premium material: the cr10 nozzle are made of high quality brass material, Against rust or erosion,sturdy and durable, connect with M6 out thread, easy to install
- Parameter: input diameter 1.75mm
- output diameter 0.2mm, 0.4mm, 0.6mm, 0.8mm, 1.0mm
- out thread: M6,different sizes can meet your multiple needs.
- NOTE: After replacing the nozzle, please recalibrate the distance between nozzle and build plate to ensure the quality of print parts.
Description
Specifications:
Type:cr10 nozzle
Material: Brass of National standard
Out Thread: M6
Filament Diameter: 1.75mm
Output Diameter: 0.4mm
Quantity: 0.4mmX22 pcs
Compatibility: with all 1.75mm ABS/ PLA 3D printer, work well with Monoprice select mini,Prusa i3, Anet8. Installation: external M6 thread connection
Description:
How to replace nozzles ?
Step 1: Turn on 3D printer, heat the nozzle and heat block to the target temperature (PLA: 180-220, ABS: 240-280).
Step 2: After heat finishing, close printer, take spanner to hold the heat block. Then use socket screwdriver to screw old nozzle extruder out.
Notice: Please don’t touch the old nozzle and heat block to avoid scalding.
Step 3: Spanner keep to hold the hear block, use the socket screwdriver screw the new nozzle in, make sure tight.
Notice:
Small parts, please keep away from children.
5. ExcelFu 5pcs Length Extruder 1.75MM Teflon Throat Tube and 5pcs 0.4MM Brass Extruder Nozzle M6 Threaded and 5pcs Heater Blocks Hotend for E3D V6 RepRap 3D Printers (Bonus: 2pcs hex Key Wrenches)
6. 3D Printer Nozzle Heater Kit, Aluminum Heater Block +1.75mm Extruder Teflon Throat Tube M6 Thread +0.4mm Brass Extruder Nozzle +Silicone Heater Socks for E3D V6 Makerbot RepRap 3D Printers (20 PCS)
Feature
- ❃❃ This stainless steel barrel has continuous thread so it is more universal than our standard barrel. It also has been drilled out larger at one end and a piece of PTFE teflon tube(Not included) can be inserted to reduce the chances of “barrel lock” which can stop filament feeding resulting in a failed print and otherwise only solved with the oily rag trick
- ❃❃ These blocks are engineered for ultimate high temperature performance. These blocks are perfect for high temperature applications while working perfectly with everyday filaments like PLA, ABS and spoolworks EDGE.
- ❃❃ These socks will keep your nozzle clean and free of burnt on blackened plastic. They don’t just keep the nozzle clean, but also keep heat inside the hotend, and off the print.
- ❃❃ With silicone socks on will stop heat loss and unstable temperatures for good. Insulated with high-temperature silicone, this E3D v6 heater block kit will maintain a stable temperature much better.
- ❃❃ Come with 5 Pcs 0.4mm nozzle, which made of solid and durable high precision brass material, it is wear resistant, can provide a long service life.
Description
Specification of Silicone Heater Socks:
Material: Silicone
Size: 20*16.5*12.5mm
Specifications of the Extruder Heat BreakTube:
Material: stainless steel
Overall length: 22mm
Upper Thread: M7 (Heatsink end)
Lower Thread: M6 (Heater block end)
Filament size: 1.75mm
Specification of Brass Nozzle:
Type: 0.4mm Extruder Brass Nozzle PrintHead
Color: Golden.
Material: Brass
Input Diameter:1.75mm
Output Diameter:0.4mm
Specification of Heater Blocks:
Name: Metal Part
Color: Silver
Size: 20*16*12mm
Screw: M6 and M3
Heating: 6mm
Thermocouple: 3mm
Package list:
5PCS X Brass Nozzle
5PCS X Extruder Tube
5PCS X Heater Blocks
5PCS X Silicone Heater Socks
7. Ewigkeit MK8 Silicone Sock Heater Block Cover MK7/8/9 Hotend for Creality CR-10,10S,Ender 3,Anet A8 3D Printer(not Include Heater Block))
Feature
- MK8 Silicone made of heat-resistant, non-stick silicone material ,much more durable and functional ,better than before PTFE tape and heat resistant cotton
- Ender 3 Silicone cover fit for 0.78″/20mm x 0.78″/ 20mm x 0.39″/ 10mm heater block,Helps to keep the hotend temperature extremely stable
- Anet A8 silicone can extend the life of the heater block and keep your heater block clean from burnt and blackened plastic
- Mk9 silicone socks just for MK7/MK8/MK9 Makerbot heater block,not for e3d v6 and MK10
- High temperature resistance can reach to 280℃ ,Color is blue,not include heater block
8. MakerHawk 5pcs Aluminum Heater Block for MK7 / MK8 3D Printer and 5pcs NTC 3950 100K Thermistor with 1 Meter Wiring and 5pcs 12V 40W 620 Ceramic Cartridge Heater for 3D Printer
Feature
- 3d printer heater block: Inner hole for set screw: M6 and M3 (heat pipe and thermocouple).
- 12V 40W 620 Ceramic Cartridge Heater: Resistance: Material: 304 stainless steel
- Lead wire: 0.3 square
- 2080 high temperature resistant high quality oxide powder.
- NTC 3950 100K Thermistor: For 3D printers: use TEMP_SENSOR 11 in Marlin firmware
- Resistance value at 25°C=100K
- Cartridge Heater: The solids, liquids, and gases need to be heated by cartridge heater, transmit heat quickly by conduction if the producer of the heat (the cartridge) is in direct contact with the heat sink (any solid, liquid, or gas)
- Widely used for manufacturing plastic and rubber parts in the car industry or in the food processing industry, etc
- We have a strong after-sales team, if you have any questions, please feel free to email us. Click on “MakerHawk-US”,then “Ask a question”.We will reply to you as soon as possible. Thank you for your cooperation!
Description
3d printer heater block:
Inner hole for set screw: M6 and M3 (heat pipe and thermocouple)
Heater Mounting Hole: 6mm diameter
Thermocouple Mounting Holes: 3mm diameter
Suitable for Makerbot printer
12V 40W 620 Ceramic Cartridge Heater:
Material: 304 stainless steel
Lead wire: 0.3 square
Resistance: 2080 high temperature resistant high quality oxide powder
Application:
1 Semiconductor chamber heating
2 Semiconductor wafer lead connection
3 Semiconductor wire and die bonding
4 Freeze protection and deicing of equipment in cold climates or applications
5 Humidity Control
6 Patient Comfort heating used in medical devices
7 Mold die and platen heating
8 Seal bars used in packaging equipment
9 Test sample heating in gas chromatography
NTC 3950 100K Thermistor:
For 3D printers: use TEMP_SENSOR 11 in Marlin firmware
Small Size: 1.25mmx2.0mm glass bead
High accuracy: 1%
Resistance value at 25°C=100K
Wiring insulation: high temperature teflon / PTFE
Package Including
5 * 3d printer heater block
5 * 12V 40W 620 Ceramic Cartridge Heater
5 * NTC 3950 100K Thermistor
9. Maxiwatt Hotend for Printer 3D – The hot end Cylinder Heater Core + THERMISTOR + Block Circular – Block Heater – Heat More Precise REPRAP EXTRUSOR 24V 40W
Conclusion
By our suggestions above, we hope that you can found Copper Heating Block 3D Printer for you.Please don’t forget to share your experience by comment in this post. Thank you!