827 reviews analysed
1. Aibecy 12/24V Heatbed Heat Bed Power Module Expansion Board Heating Bed Accessories High Power Expansion Module for CR-10/CR-10S Series Mosfet Board 3D Printers Hot Bed 1Pcs
Feature
- This power module expansion board is a perfect assistant for your 3D printers, for better printing effects.
- Suitable for Creality CR-10, CR-10S, CR-10 MINI, CR-10 S4, CR-10 S5, etc.
- Compact appearance and fine workmanship.
- Made of premium PCB material, high quality and durable.
- 100% brand new and good performance.
Description
Features:
This power module expansion board is a perfect assistant for your 3D printers, for better printing effects.
Suitable for Creality CR-10, CR-10S, CR-10 MINI, CR-10 S4, CR-10 S5, etc.
Compact appearance and fine workmanship.
Made of premium PCB material, high quality and durable.
100% brand new and good performance.
Specifications:
Creality 3D
Material: PCB
Quantity: 1pcs
Suitable: For Creality CR-10, CR-10S, CR-10 MINI, CR-10 S4, CR-10 S5, etc
Applicable Range(hot bed power): 300-850W
Supply Voltage: 12V/ 24V
Item Size: 5.3 * 3.8 * 2.5cm / 2.1 * 1.5 * 1in
Item Weight: 24g / 0.8oz
Package Size: 10.5 * 6.2 * 5.6cm / 4.1 * 2.4 * 2.2in
Package Weight: 56g / 2oz
Package List:
1 * Heatbed Expansion Board
Note:
Cannot be used for power supplies above 30V, be careful not to reverse.
2. Creality 3D Printer NTC Thermistor Temp Sensor 100K for Ender 3 / Ender 3 Pro/Ender 5 / CR-10 / CR-10S
Description
Package included: 5pcs thermistors
Application : Heated bed or extruder of Reprap Prusa I3 3D Printer
Resistance value at 25°C=100K
Thermistor: small size 1.25mmx2.0mm glass bead
Wiring insulation: high temperature Teflon/PTFE.
3. Creality Original 3D Printer Extruder Assembled Full Set Replacement Part MK8 Hot End Kit for CR-10 / CR-10S / CR-10 S4 / CR-10 S5 (CR10 extruder Full Set)
Feature
- 100% original Creality 3D Printer accessories for CR10/ CR10S/ CR10S4/ CR10S5
- This CR-10 extruder can work with different sizes of MK8 nozzle: 0.2mm 0.3mm 0.4mm 0.5mm 0.6mm 0.8mm 1.0mm
- Tip of the nozzle, aluminum heating block, throat pipe (built-in Teflon)
- MK8 Extruder Hot End Kit With thermistor and Heater,12V 40W
- Thermistor and heater cable length: 1M
Description
Package: 1x Aluminum block 1x Heating tube (heating tube 1 m long, 12V 40W) 1x 1.75MM 0.4MM Brass Nozzle 1x M6*30mm Throat pipe (built-in Teflon) 1x Thermistor + Brass sleeve (1 meter long)
4. MK8 Extruder Hot End Part Assembled DIY Hotend, 0.4mm Nozzle 12V 40W Heater Including for RepRap、CR 10 3D Printer 1.75mm Filament
Feature
- Package include:22 pcs 3d printer nozzles (output diameter ) 22 x 0.4mm, With storage box packaging.
- COMPATIBILITY: mk8 nozzle are compatible with Anet A8, Creality CR-10, Tevo Tarantula, MK8 makerbot, duplicator, prusa i3 and reprap,Compatible with all 1.75mm ABS/ PLA 3D printer.
- Premium material: the cr10 nozzle are made of high quality brass material, Against rust or erosion,sturdy and durable, connect with M6 out thread, easy to install
- Parameter: input diameter 1.75mm
- output diameter 0.2mm, 0.4mm, 0.6mm, 0.8mm, 1.0mm
- out thread: M6,different sizes can meet your multiple needs.
- NOTE: After replacing the nozzle, please recalibrate the distance between nozzle and build plate to ensure the quality of print parts.
Description
Specifications:
Type:cr10 nozzle
Material: Brass of National standard
Out Thread: M6
Filament Diameter: 1.75mm
Output Diameter: 0.4mm
Quantity: 0.4mmX22 pcs
Compatibility: with all 1.75mm ABS/ PLA 3D printer, work well with Monoprice select mini,Prusa i3, Anet8. Installation: external M6 thread connection
Description:
How to replace nozzles ?
Step 1: Turn on 3D printer, heat the nozzle and heat block to the target temperature (PLA: 180-220, ABS: 240-280).
Step 2: After heat finishing, close printer, take spanner to hold the heat block. Then use socket screwdriver to screw old nozzle extruder out.
Notice: Please don’t touch the old nozzle and heat block to avoid scalding.
Step 3: Spanner keep to hold the hear block, use the socket screwdriver screw the new nozzle in, make sure tight.
Notice:
Small parts, please keep away from children.
5. KEENOVO Silicone Heater 508x508mm(20"x20") 1300W for Creality CR-10 S5 3D Printer Bed w/Screw Holes (120V)
Feature
- Excellent heat source for your Creality CR-10 S5. Designed in profiled heating circuit for evener heating performance across the whole surface.
- 508mm x 508mm ( 20″ x 20″), 1300W, with 3M PSA and NTC thermistor
- Comes with 24 pre-made screw holes. Custom Heater Design Welcome
- ***Caution!*** Before buying, please check if the 24 hole pattern conforms to that of your build plate. Pattern view from the adhesive side of this heater pad must be same to the front view pattern of your 24 hole build plate.
- Item Location: Shanghai, China
Description
IMPORTANT NOTE: This is developed to fit the recent update Creality made to the S5 aluminum plate with 24 holes. This fits the old version of 4 holes also. Creality may further update this aluminum plate without prior notice. Please kindly check if this one fits your printer before the purchase. Please heat only when after it’s mounted onto the build plate (Aluminum plate recommended). A supporting frame/layer is strongly suggested to have the heating element “sandwiched” tightly for better heating result. Any questions, message us. Response within 24 hours guaranteed.
6. Creality Upgraded CR-10 V2 Silent Board, V2.5.2 Silent Motherboard Mainboard Control Board with TMC2208 Driver for CR-10 V2 3D Printer
Feature
- Compatible: Upgraded silent mainboard for Creality CR 10 V2 3D Printer, just plug it in and you could start printing.
- Super Quiet and Noise Reduction. Use TMC2208 Stepper Motor Drivers, which the key component to eliminate the printers motor when printing.
- Bootloader pre-installed. The firmware can be modified by ARDUINO or Cura with the USB cable. Use special power chip, support 24V input voltage.
- Concern for safety. Thermal runaway protection is enabled, if the temperature rises out of control, the printer will stop heating and halt automatically.
- Only the CR-10 V2 firmware is pre-installed. If you want to install it in other machines, you need to refresh the other firmware.
Description
Specifications:
.Material: PCB
.Product Weight: 125g
Package Content:
.1 x Mainboard
7. Creality Upgraded Board Mainboard V2.4.1 Motherboard for CR-10S Pro 3D Printer
Feature
- Application: Replacement board for Creality CR-10S PRO 3D Printer.
- Function: The circuit board is optimized by circuit, can effectively solve the heating problem.
- Special power chip is adopted to support 24V power input.
- Easy to Use: With USB interface, easy to operate.
- Can be used with E/Z/Y/X axis motor.
Description
.Firmware: V2.4.1 version;
.Voltage: 24V input voltage is adopted
Specifications:
.Material: Circuit Board
.Product Weight: 86g
Package Content:
.1 x CR-10S Pro Mainboard
8. Heating Control Module,Entweg 3D Printer Hotbed Heating Controller High Current Load MOS Module MOSFET Board Exceed 30A Compatible for CR-10 Ender-3 Prusa TEVO 3D Printer
Feature
- Functional test has been done for each one.
- The MOS tube performance is excellent, nominal maximum current is 280A.
- Maximum current can be up to 30A or more due to extra large heat sink.
- Can use heatbed output signal of Ramp1.4 and series to control.
- Can use digital signal of 5-24V to control.
Description
Specifications:
Material: PCB
Function: Control Hot Bed, Heated Print Head
Power Supply: 12V-24V
Compatibility: For CR-10/ Ender-3/ Prusa/ TEVO/ BLV/ MGN/ Cube 3D Printer
Module Size: 8.8 * 6.7 * 3cm/ 3.5 * 2.6 * 1.2in
Module Weight: 127g/ 4.5oz
Package Size: 15 * 10 * 3.7cm/ 5.9 * 3.9 * 1.5in
Package Weight: 191g/ 6.7oz
Usage:
1. Plug a power supply;
2. Connect to heated bed;
3. Connect digital control signal to GND, D8 of MINI;
4. Connect to the heated bed signal on Ramps1.4 or series controller boards.
Packing List:
1 * MOS Module
1 * Double Head Power Cord
1 * Red Power Cord
1 * Black Power Cord
1 * Connection Cable with PINS
4 * U-shaped Terminal
9. Entweg 3D Printer,12/24V Heatbed Heat Bed Power Module Expansion Board Heating Bed Accessories High Power Expansion Module for CR-10/CR-10S Series Mosfet Board 3D Printers Hot Bed 5Pcs
Feature
- This power module expansion board is a perfect assistant for your 3D printers, for better printing effects.
- Suitable for Creality CR-10, CR-10S, CR-10 MINI, CR-10 S4, CR-10 S5, etc.
- Compact appearance and fine workmanship.
- Made of premium PCB material, high quality and durable.
- 100% brand new and good performance.
Description
Specifications:
Material: PCB
Quantity: 5pcs
Suitable: For Creality CR-10, CR-10S, CR-10 MINI, CR-10 S4, CR-10 S5, etc
Applicable Range(hot bed power): 300-850W
Supply Voltage: 12V/ 24V
Item Size(single): 5.3 * 3.8 * 2.5cm / 2.1 * 1.5 * 1in
Item Weight(single): 24g / 0.8oz
Package Size: 16.3 * 14.5 * 5.8cm / 6.4 * 5.7 * 2.3in
Package Weight: 190g / 6.7oz
Package List:
5 * Heatbed Expansion Board
Note:
Cannot be used for power supplies above 30V, be careful not to reverse.
Conclusion
By our suggestions above, we hope that you can found Cr10 Board Heating for you.Please don’t forget to share your experience by comment in this post. Thank you!
